Ever noticed how many bra-straps you might see hanging out, just going about your regular daily activities? It is simply overwhelming, they are everywhere, and not very attractive to say the least! At InvizaWear^TM we believe it will soon be a fashion faux pas if your bra-straps can be seen.

Typically, they are attached to the front side of the shoulder seam in most garments. For best results, pre-wash the article of clothing, using no fabric softener in the washer or dryer. Preheat dry iron to the silk setting, no steam. Place the INVIZASTRAP™ in position, with the adhesive side of the center panel against the garment. The softest side of the hook and loop material should be nearest the shoulder side of the garment, while the rougher side should be closest to the neck portion of the garment. Place and move the tip of the iron over the center panel only, while applying medium pressure (especially to the creases) for 3 to 5 seconds, repeat. Allow to cool before folding side panels over and using. Use caution with delicate fabrics, not recommended for any kind of sheer, light weight or ‘see through’ type fabrics.

1. If you are having trouble finding the correct position for applying the INVIZASTRAP™, get a few pieces of tape, about 3/4” each. Put the garment on inside-out, find the position you would like your bra-straps to stay in. Place the tape there, to the front side of the shoulder seam. This will mark the proper position for applying the INVIZASTRAP™, place garment on the ironing board, remove the tape and apply.
2. Do not overheat – use the low setting on your iron, with no steam. Overheating will cause an insufficient bond. If this occurs reapply a new INVIZASTRAP™ in the same position. Each INVIZASTRAP™ is good for one application only.

Keep the INVIZASTRAP™ in the folded position when putting on or taking off the garment and when laundering. Wash in lukewarm or cold water with permanent press or delicate cycle, dry on low heat, do not dry-clean.

The INVIZASTRAP™ is available exclusively through our website or by mail with a check or money order made payable to InvizaWear™.

All InvizaWear™ products are manufactured in the United States. The INVIZASTRAP™ is handcrafted in Oklahoma City.

The INVIZASTRAP™ was developed by Michelle Cain, InvizaWear™

We wanted a name that described exactly what we do, (keeping your undergarments invisible!) short and simple, yet catchy and alluring. We traded the soft, curvy “s” for a hip, edgy “z”, changed the “i” to an “a”, we are from the South, after all! Hence the name, InvizaWear™

If for any reason, you are not fully satisfied with our products, you may return the items by UPS or USPS Priority Mail to our Corporate Office. You have 14 days from the time you receive your purchase to return or exchange any merchandise when accompanied by an original sales receipt. Products must be in their original packaging and undamaged. You must call or email the customer service department at InvizaWear™ for authorization to return purchased merchandise. All shipping costs are the complete and sole responsibility of the consumer.

By using the InvizaWear™ website, you agree that the use of the InvizaWear™ website is at your sole risk. Under no circumstances shall InvizaWear™ be liable for any direct, indirect, incidental or consequential damages that may result from your use or inability to use this site. The InvizaWear™ website is provided on an ‘AS IS’ and ‘as available’ basis. User acknowledges that this paragraph shall apply to all content, merchandise and services available through the InvizaWear™ website.
The INVIZASTRAP™ is attached to a garment using a permanent, acid free, iron-on adhesive. The INVIZASTRAP™ is intended to be permanently attached to the article of clothing. If the INVIZASTRAP™ is removed from the garment, there may be some iron-on adhesive left on the inside of the garment, where the INVIZASTRAP™ was attached (it will not be sticky). If this occurs, you may consult your dry-cleaner about an adhesive remover or you may try a product called Un-Du in an attempt to remove the adhesive. Un-Du is a liquid adhesive remover that will assist in dissolving the adhesive in the fabric. InvizaWear™ does not guarantee any of the removal processes listed above, nor do we accept responsibility for any article of clothing, or any items used applying the INVIZASTRAP™ to the garment. Apply and use the INVIZASTRAP™ at your own risk.